Using External Flashes in the TTL Mode

What is TTL Anyway?

We suggested that the external flash be set to the TTL mode. The TTL (i.e., Through The Lens) mode means that the camera will measure the output of external flash and stop the flash once illumination is sufficient. This is the easiest mode of using external flashes. However, do keep in mind that the Coolpix 950 is not true TTL cameras in terms of flash control. It measures flash illumination with a flash sensor next to the on-camera lens as shown below. As a result, what this sensor sees is usually not what the lens sees. We shall refer to this as TTL because the camera still has the control.

The external flash can be used in both A-REC or M-REC. Moreover, it can operate in AUTO, SLOW (i.e., Slow Synchronization), and Anytime mode.

Using External Flash in A-REC

The information of this section are not discussed in Nikon's manual and are obtained mainly through extensive experiment.

If the internal flash is not turned off, then we have the following possible situations:

  1. If the camera sensor determines the existing illumination is sufficient, neither the internal nor the external flash will fire.
  2. If the existing illumination is not bright enough but not so dark, the external flash fires but the internal flash does not.
  3. If the existing illumination is insufficient, then both flashes fire. In fact, if the external flash does not provide sufficient illumination, the internal flash fires. You can test this by covering the external flash or turning the external flash off.
Because of the second point above, it is difficult to predict when the internal flash will fire. Therefore, even though the camera is in A-REC, turning off the internal flash will provide a better flash control.

The Aperture-Priority Mode

In the Aperture-Priority mode, you select an aperture and the camera chooses an appropriate shutter speed. Because an external flash is being used, the camera will set the shutter speed to the flash synchronization speed (i.e., 1/60 or 125 sec). When you press the shutter-release button, the flash fires. The flash sensor measures the illumination and stops the flash when the illumination under the given aperture is sufficient. There are two extreme cases. One, if the flash illumination is not enough, the camera will force the flash to put out more power until the illumination is right. However, it is possible that the external flash being used does not have the needed power (i.e., GN is not large enough). If this happens, your image will be under-exposed, and you need to use a larger aperture. Two, if the flash illumination is more than necessary, the camera will force the external flash to cut down its power. However, it is possible that the power of the external flash is so strong that it has already reaches its lowest power level. In this case, your image will be over-exposed due to too much flash illumination and you should consider to use a smaller aperture or move your external flash away from the subjects.

To illustrate this TTL working style, let us take a look at the following five images. They were taken under the synchronization shutter speed with apertures F9.8, F7.8, F6.2, F4.9 and F3.5. The smaller cat in the far end gives a feeling of depth of field. Note that the larger the aperture you use, the shallower depth of field you get. Thus, for small apertures such as F9.8 and F7.8, the smaller cat is quite sharp in the images. On the other hand, the smaller cat is out of focus in images taken with larger apertures (e.g., F4.9 and F3.5). If you compare these five images, you will find out that exposure in the images of F9.8, F7.8 and F6.2 are similar except that the depth of field levels are different. The image taken with F4.9 is slightly brighter than the images on the top row. This means it is slightly over-exposed. Check the texture on the larger cat and you will see the difference. The image taken with F3.5 is definitely over-exposed because the larger cat's texture is washed out. As mentioned earlier, to overcome this problem, you can use a smaller aperture or move the external flash away from the subjects.

F9.8 F7.8 F6.2
F4.9 F3.5
Click on the image to see a larger one

The Shutter -Priority Mode

In the shutter-priority mode, you select a shutter speed and the camera chooses an aperture. But, how about the flash synchronization speed? Can we choose a shutter speed that is different from the flash synchronization speed? The answer is "yes" and "no." If your scene is mainly illuminated by the flash, it does not matter what shutter speed you use. The flash sends out its light in a duration that is much shorter than the highest shutter speed. Because the only light source is your flash, after a flash light burst, the scene will not be illuminated and, as a result, the image capturing device will not be able to pick up the remaining ambient illumination even though the shutter is still open. However, if the ambient illumination is strong, the image capturing device will pick up some extra ambient light after the flash burst. Hence, in addition to the properly illuminated subjects by the flash light, subjects may pick up a touch of the ambient light. This is exactly what slow synchronization means. However, if the ambient light is too strong, adding a flash light without further control will likely give you an over-exposed image.

The following images illustrate the use of different shutter speeds and the chosen apertures (by the camera). The shutter speeds used were 1/500, 1/60, 1/15, 1/2, 2 and 8 sec, and the aperture values selected by the camera were F4.9, F4.9, F4.9, F4.9, F6.9 and F9.8. As you can see, F4.9 are used with four different shutter speeds. Although 1/500 sec is 256-fold faster than 1/2 sec, the image taken with 1/2 sec and F4.9 is only slightly over-exposed and is not very different from the ones taken with 1/500 and F4.9. This is because the ambient light is not strong and the one taken with 1/2 and F4.9 can be viewed as a slow synchronized version of the other three. However, even though the apertures were closed down to F6.9 and F9.8, the last two images, especially the last one, are over-exposed. These images show that the camera is not very good at shooting flash illuminated images in the shutter-priority mode. Therefore, staying with aperture-priority node is a better idea.

1/500 sec F4.9 1/60 sec F4.9 1/15 F4.9
1/2 sec F4.9 2 sec F6.9 8 F9.8
Click on the image to see a larger one